NEC VERSA P600 User Manual

NEC Versa P600 Disassembly Manual

NEC Versa P600 Disassembly Manual Page 10 Fig. 12 Removing Heat plate from base unit Note: When assembling the heat plate, make sure that these

NEC Versa P600 Disassembly Manual Page 11 Removing the Wireless Module To remove the Wireless Module, first remove the keyboard cover (see Removing

Fig. 15 Releasing the heat sink screws Note: When assembly the heat sink, tighten the heat sink screws according to the ascending order (1234).

NEC Versa P600 Disassembly Manual Page 13 Removing the LCD Module To remove LCD Module, first remove the Keyboard Cover (see Removing the keyboard c

NEC Versa P600 Disassembly Manual Page 14 Fig. 20 LCD hinge screws at the rear 4. Unscrew the two screws located on the bottom of the unit as s

Removing the LCD Panel To remove the LCD Panel, first remove the LCD Module (see Removing the LCD Module), then perform the following steps: 1. Unsc

NEC Versa P600 Disassembly Manual Page 16 Fig. 24 Removing the inverter board screws 4. Carefully lift up LCD panel and disconnect the LCD cab

Removing the Top Cover To remove the Top Cover, first remove the Keyboard Cover (see Removing the keyboard cover), remove the keyboard (see Removing t

NEC Versa P600 Disassembly Manual Page 18 Fig. 28 Battery Compartment 5. Carefully lift up and release the top cover and put it aside. Fig. 29

NEC Versa P600 Disassembly Manual Page 19 1. On the other side of the top cover unscrew the two screws on the Touch Pad assembly as shown in Fig. 3

NEC Versa P600 Disassembly Manual Page 2Table of contents Overview...

NEC Versa P600 Disassembly Manual Page 20Removing the DC/DC Board To remove the DC/DC board, first remove the Top Cover (see Removing the Top Cover

NEC Versa P600 Disassembly Manual Page 21 Removing the Main Board To remove the Main board, first open the Top Cover (see Removing the Top Cover), r

NEC Versa P600 Disassembly Manual Page 22 Fig. 35 Removing Main Board DIP Switch Setting Fig. 36 DIP Switch position Dip Switch Description S

NEC Versa P600 Disassembly Manual Page 23 Screws M2.5x5.6 Silver M2.5x3.5 Silver M2.5x8 Sliver M2.5x10 Silver M2.5x11 Black M2.5x12.5

NEC Versa P600 Disassembly Manual Page 24Notice The information in this guide is subject to change without notice. This guide contains information

NEC Versa P600 Disassembly Manual Page 3Overview This document contains step-by-step disassembly instructions for the Versa T400 chassis. The instru

NEC Versa P600 Disassembly Manual Page 4Hazardous Voltage There is hazardous voltage present inside the computer when it is connected to an AC suppl

Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the Versa P600. 2. Turn the unit upside down. 3.

2. Lift up the hard disk drive and disconnect it as shown in Fig. 3 Fig. 3 Disconnecting the hard disk drive 3. Unscrew the four screws on both s

2. Carefully lift up MDC modem module. 3. Disconnect the cable attached to the MDC modem and put the modem aside. Removing the Keyboard Cover NEC

NEC Versa P600 Disassembly Manual Page 81. Remove the screws as shown in Fig. 8 Fig. 8 Removing the screws holding the keyboard Note: The screw

NEC Versa P600 Disassembly Manual Page 9 Fig. 10 Removing the screws on Heat Plate Note: If you want to disassemble the Optical Drive, you are re