Nec 2400IPX User Manual

DTERM®SERIES iDTERM®IPUSER GUIDENEAX®2400IPXInternet Protocol eXchange*NEC-405 NEAX2400 UG #2 1/22/03 2:42 PM Page I

S-SPD (Speed Calling – System)Allows a station user to call certain frequentlydialed numbers using fewer digits (abbreviatedcall codes) than would nor

HSET (Headset)Allows the user to go off- and on-hook whenusing the headset.RLS (Release Key)Allows the user to release the current call whenusing the

10TERMINAL SETUP WITHTHE UP/DOWN KEYNote: Not Displayed for Dterm 65/Dterm Series IIIand Dterm 75/Dterm Series E mode. Dterm Series III/Dterm Series E

11TERMINAL SETUP WITHTHE FEATURE KEYMICROPHONE ON/OFFLED on Mic key shows the status of the built-inmicrophone.To change microphone status:◆ Press Sof

TONE NO. FREQUENCY (HZ)MODULATION (HZ)1 520/660HZ 16HZ2 520/660HZ 8HZ3 1100/1400HZ 16HZ4 660/760HZ 16HZ5 MELODY 16 MELODY 27 MELODY 38 MELODY 49 MELOD

13TO ADJUST TRANSMISSION/RECEIVING VOLUMEHandset volume can be changed.◆ Press Feature and 4. The LCD displaysthe current volume.◆ Press Feature and

TO ORIGINATE ANOUTSIDE CALL◆ Lift handset or press Speaker key, receive dialtone.◆ Dial the Central Office access code, e.g. 9.◆ Dial desired telephon

17MULTILINE APPEARANCETO ORIGINATE◆ Press the MULTILINE APPEARANCE feature key.◆ Lift handset or press Speaker, receive CentralOffice or distant PBX d

TO VERIFY (WITH DTERM 8D/16D/32D)◆ Press Feature button.◆ Press desired Speed Dial button.◆ Display indicates digits programmed.Note 1: To program a h

TO ORIGINATE A CALLUSING SPEED CALLING –SYSTEMTO PROGRAM SPEEDCALLING – SYSTEMKEY(ON ONE-TOUCH SPEED CALLING KEY)◆ Press Feature key.◆ Press desired o

LIABILITY DISCLAIMERNEC AMERICA, INC. RESERVES THE RIGHT TO CHANGE THE SPECIFICATIONS,FUNCTIONS, OR FEATURES, AT ANY TIME, WITHOUT NOTICE.NEC AMERICA,

Note 1: A Voice Call may be programmed on a one-touch speed key by pressing Speed Dial button,dialing the extension and pressing the Transfer key.(V d

TO ANSWER A VOICECALL HANDS-FREE◆ Receive incoming Voice Call.◆ Press the MIC Soft Key or Mic. LED lights.◆ Respond hands-free.NOTE: If privacy isrequ

MANUAL INTERCOMTO INITIATE◆ Press MICM, lift handset or press Speaker, ringback tone is heard.◆ Press the SIG key if it is desired for the calledstat

◆ Lift handset or press Speaker, LED lights solid green.◆ If called station is engaged in a non-intercomcall, the station may press MICM after placing

◆ If called station is engaged in a non-intercomcall, the station may press DICM after placingthe original call on hold (with the Hold key.)26TO PLACE

IF UNANSWERED◆ After preprogrammed time, Automatic Recallis initiated.◆ Visual and audible signal (rapid flash and ringburst) is sent to station that

TO TRANSFER A CALL◆ After conversing, ask party to hold.◆ Press Transfer. Receive interrupteddial tone.◆ Dial destination station’s extensio

29CONFERENCE◆ With call in progress, ask party to hold.◆ Press Transfer, receive interrupted dial tone.◆ Dial desired number.◆ After call is

30TO ESTABLISH A BROKER CALL◆ While engaged in a call and wishing toconsult a third party, press Transfer. Caller isautomatically placed on hold.◆ Dia

CALL PICK-UP (GROUP)WHEN A STATION WITHIN PICK-UPGROUP RINGS◆ Lift handset.◆ Press CALL PICK-UP or dial “Call Pick-up”access code (may be stored on on

TABLE OF CONTENTSKEYS AND LAMPS 2SOFT KEYS 4TERMINAL SETUP WITH THE UP/DOWN KEY 10TERMINAL SETUP WITH THE FEATURE KEY 11LOGIN/LOGOUT(IP ENABLED DTERM/

35WHEN A STATION WITHIN THESYSTEM RINGS◆ Lift handset, receive dial tone.◆ Press PICK-DIRECT and dial the station numberto be picked up.– OR–◆ Dial “

OFF-HOOK TRUNKQUEUING◆ Press Speaker, receive dial tone.◆ Dial “Off-hook Queuing” access code.◆ Dial desired telephone number. Encounter atrunk busy c

LAST NUMBER REDIALTO RECALL THE LAST NUMBER DIALED◆ Press Redial. Last number dialed is displayed.◆ Press Redial key until desired number isdisplayed.

CALL FORWARDING –ALL CALLSTO SET◆ Press Speaker. Receive dial tone.◆ If setting for another station, press MULTILINE APPEARANCE.◆ Press FWD or dial “C

TO CANCEL◆ Press Speaker. Receive dial tone. If cancellingfor another station, press MULTILINEAPPEARANCE.◆ Press FWD or dial “Call Forwarding –All

40USING THESOFTKEY◆ Press FDB Soft Key. Receive special dial tone.◆ Dial destination; wait for service set tone.◆ “FORWARD SET” is displayed; CallForw

41◆ Press Speaker. Call Forwarding – Don’t Answer is set. USING THE SOFT KEY◆ Press FDN Soft Key. Receive special dial tone.◆ Dial destination;

42TO CANCEL◆ Press Speaker. Receive dial tone. If cancellingfor another station, press MULTILINEAPPEARANCE.◆ Press FWD-NA or dial “CallForwarding

44TO CANCEL◆ Lift handset or press Speaker key; receive DialTone.◆ Dial “Logged Out IP Station – CallDestination” cancel code; receive service settone

Option 4◆ Boss presses Answer and converses withSecretary. Trunk A is placed on hold.◆ Boss denies call, presses Transfer to return toTrunk A.◆ Secret

KEYS AND LAMPSPROGRAMMABLE KEYSThese are examples of Dterm®features available by pressing the programmable keys. Some features may be programmedby the

Note 1: Station A can be a single-line station if itappears on the Station B Dterm.Note 2: Up to six parties can break into a two-partyconversation (a

INDEXAAccount Code 20Answering a Camped-on Call 30Answering a Message 48Answering a Voice Call Hands-free 23Authorization Code 21Automatic Interc

FForced Account Code 20Function Keys and Lamps 2HHeadset Key 9Help 5Hold 26IInternal Call Origination 16LLast Number Redial 37Leave a Message 47

PPaging Transfer 50Placing a Call on Exclusive Hold 27Placing a Call on Hold 26Privacy 57Privacy Release 58SSaving and Repeating a Number 46Speed

LCD DISPLAYS15:39 DDD XTime elapsed, trunk type and number for outsidecall. Time elapsed for parked call.XXX DDD XParked call retrieved from a remote

C WAIT XXXX ORC WAIT SET XXXXCall Waiting tone sent to or received at busystation show in called or calling number.Call received on boss’ station fr

Call Forwarding – All Calls.Call Forwarding – Busy Line.Call Forwarding – Don’t Answer.Logged Out IP Station – Call Destination.HHANDS-FREE ON/OFFHand

LOGINThe IP Enabled Dterm becomes operationalwhen the user enters “Login Code” and“Password.”LOGOUTPress preassigned Logout button to logout.MMSG XXXX

OVERRIDE XOverriding intercom call through bridging.Automatic Intercom.Dial Intercom.Manual Intercom.OVERRIDE XXXXExecutive Override.PPICK UP XXXX X

RRCV VOL. SMALL/LARGEReceiver Volume status.RINGER TONE XReady for Ringer tone selection.SSPEED SETSpeed Calling number saved in memory.TTRANSFERRead

LAMPSCall Indicator LampLamp at top of Dterm Display flashes when acall terminates to the terminal. Lamp lightssteadily when a message has been left.L

VOICE BUSY/RESTVoice Call station called is busy or restricted.WWAIT P-RLS?Prompt when requesting privacy release atanother station.69*NEC-405 NEAX240

70FACE LAYOUT1 CALL INDICATOR LAMPLamp at top corner of Dterm Display flashes when acall terminates to the terminal. Lamp lights steadilywhen a messag

14 MICROPHONEBuilt-in microphone is used for hands free operationwith speakerphone.15 UP/DOWN( ▼ DOWN ▲ UP)Used to adjust LCD contrast, speaker/receiv

2580OPERTUVJKLABC36#9DEFMNOWXYZ147GHIPQRSDirectoryMessageSpeakerAnswerRedialRecallFeatureMicConfHoldTransferExitHelp12345678910111213151617141819DTERM

2580TUVJKLABC36#9DEFMNOWXYZ147GHIPQRSSpeakerAnswerRedialRecallFeatureDirectoryMessageMicConfHoldTransferCall Indicator LampDedicated Function KeysMicr

NEC America, Inc.Corporate Networks Group6555 N. State Highway 161Irving Texas 75039Visit our Web site at www.cng.nec.com©NEC America, Inc. 2003NEAX a

FUNCTIONKEY ACTIVITIESFeature + 1 = Turns microphone on or off.Feature + 2 = Adjusts handset receiver volume.Feature + 3 = Selects ringer tone.Feature

5Exit KeyPress the Exit key to exit the Help program.Help KeyPress the Help key. Press desired Soft Key forhelpful information about that key.MIC (Mic

RINGINGBUSY(1)(2)CONNECTION CONSULTATION HOLDMIC CONF>>>2000TRANSFER(Time Display)MIC DND>>>2000(Time Display)S&R>>>2

7CW (Call Waiting)Enables a busy station to receive a secondincoming call. A camp-on indication tone is sentto the busy station, and the user can use