NEC SigmaBlade B120a User's Guide Page 263
- Page / 374
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Upgrading Your Server 9-5
INSTALLATION/REMOVAL PROCEDURE
Install or remove the devices in the following procedure.
Processor (CPU)
The server may have another CPU installed in addition to the factory-installed CPU (Intel Xeon
Processor).
IMPORTANT:
The CPU to be added must have the same specification (on the core
voltage, clock, and others) as the CPU already installed.
The CPU is extremely sensitive to static electricity. Make sure to
touch the metal frame of the server to discharge static electricity
from your body before handling the CPU. Do not touch the CPU
pins by a bare hand or place the CPU directly on the desk. For static
notes, see the section "Anti-static Measures" described earlier.
Do not operate the system until confirming that the additionally
installed CPU is in normal state.
Make sure to use the CPU authorized by NEC. Installing a third-
party CPU may cause a failure of the CPU as well as the server.
Repair of the server due to failures or damage resulted from
installing such a board will be charged.
CPU blade
CPU #1 (to be installed below the heat sink)
CPU #2 (to be installed below the socket cover)
- NEC Express5800/B120a 1
- User's Guide 1
- SAFETY INDICATIONS 3
- Attentions 4
- Prohibited Actions 4
- Mandatory Action 4
- CE Mark EMI: 5
- Australia EMI: 5
- Canada EMI: 5
- Trademarks 6
- ABOUT THIS USER'S GUIDE 8
- IN THE PACKAGE 9
- CONTENTS 10
- Chapter 1 15
- SAFETY NOTES 16
- Do not step on the cable 17
- FOR PROPER OPERATION 19
- TRANSFER TO THIRD PARTY 21
- DISPOSAL AND CONSUMABLES 22
- USER SUPPORT 23
- Advice for Health 24
- Chapter 2 25
- OVERVIEW 26
- STANDARD FEATURES 27
- PART NAMES AND CONTROLS 28
- General Description 2-5 29
- 2-6 General Description 30
- External View 31
- Lamp Indications 33
- STATUS Lamp 34
- General Description 2-11 35
- 2-12 General Description 36
- General Description 2-13 37
- LAN (1 - 2) Link/Access Lamps 38
- USING YOUR SERVER 39
- POWER lamp 40
- POWER switch 40
- Power-off of Blade Server 41
- POST Error Messages 43
- Device Identification 44
- Chapter 3 45
- BEFORE INSTALLING CPU BLADE 46
- INSTALLING THE CPU BLADE 47
- MAKING CONNECTIONS 48
- 3-6 Setting Up Your Server 50
- Blade Enclosure for details 50
- Chapter 4 51
- Starting SETUP Utility 52
- After carriage of device 55
- After storage of device 55
- 4-6 Configuring Your Server 56
- Processor Settings 56
- Advanced 57
- 4-8 Configuring Your Server 58
- Memory Configuration 58
- Security 62
- 4-16 Configuring Your Server 66
- System Management Submenu 67
- 4-18 Configuring Your Server 68
- Console Redirection Submenu 68
- BMC LAN Configuration Submenu 69
- RAID CONFIGURATION 73
- Number of required HDDs 74
- RAID level 74
- Min. Max 74
- RAID 0 1 2 74
- RAID 1 2 2 74
- Largest capacity 76
- Two HDDs required 76
- Enabling RAID Feature 78
- Configure VD(s) 79
- Exiting from the Utility 80
- Menu Tree 81
- Creating/Adding Configuration 82
- 6. Press Space 83
- Replace hard disk drive 86
- Execute rebuilding 86
- Execute Check Consistency 87
- Before Using WebBIOS 95
- Using WebBIOS 98
- Main Menu 99
- 4-50 Configuring Your Server 100
- WebBIOS Menu 100
- Controller Properties 102
- How to change setting value 104
- Scan Devices 105
- IMPORTANT: 105
- Virtual Drives 106
- Physical Drive Properties 108
- 3. Click [Go] 108
- Configuration Wizard 110
- Controller Selection 110
- Physical View / Logical View 110
- Configuring Virtual Drive 112
- 4-64 Configuring Your Server 114
- DG is added to Span 115
- RAID00 is not supported 117
- Parameters for VD Definition 120
- Operation of Various Features 122
- Manual Rebuild 124
- 1. Start WebBIOS 125
- Reconstruction 128
- Slow Initialize 132
- Number and ID 133
- Setting of Priority 135
- 4-86 Configuring Your Server 136
- Chapter 5 137
- About Express Setup 138
- Windows Server 2008 139
- About the Hardware Components 140
- SAN Boot 141
- Flow of Setup 143
- About partition size 149
- 15. Save the parameters 153
- 23. Log on to the system 156
- Microsoft Windows Server 2003 158
- Installing the Service Pack 163
- SETTING FOR SOLVING PROBLEMS 176
- 10. Click [OK] 178
- 2. Select [Advanced] tab 179
- 9. Click [OK] 181
- UPDATING THE SYSTEM 188
- Chapter 6 193
- NEC EXPRESSBUILDER 194
- OS installation 195
- Tool menu (Normal mode) 196
- Autorun Menu 198
- PARAMETER FILE CREATOR 199
- Parameter File 200
- Windows Server 2003 206
- Windows Server 2008 206
- – Windows Server 2003 209
- 14. Save the parameters 210
- 15. Saved to a floppy disk 210
- NEC ESMPRO 212
- Universal RAID Utility 213
- Remote Desktop of Windows) 214
- Installation 215
- Using Utility 215
- Uninstallation 215
- Chapter 7 217
- SYSTEM DIAGNOSTICS 218
- <Device List> 221
- <Log Info> 221
- <Option> 221
- <Reboot> 221
- 7-6 Maintenance 222
- Chapter 8 223
- SYSTEM VIEWERS 224
- ERROR MESSAGES 225
- 8-4 Troubleshooting 226
- Troubleshooting 8-5 227
- Troubleshooting 8-7 229
- SOLVING PROBLEMS 230
- Fail to power-off: 231
- POST fails to complete: 232
- Fail to start the OS: 235
- Problems with Windows 236
- Server 2003 x64 Editions 238
- Server 2003 R2 240
- The system time lags: 240
- Problems with Express Setup 242
- Product key was not asked 243
- Cannot enter standby: 244
- Cannot enter Hibernation: 244
- COLLECTING EVENT LOG 246
- MEMORY DUMP 248
- RECOVERY FOR Windows SYSTEM 249
- MAINTENANCE TOOLS 250
- Function of Maintenance Tools 252
- BIOS/FW Updating 253
- ROM-DOS startup FD 253
- Test and diagnostics 253
- System Management 253
- Starting 254
- RESETTING THE CPU BLADE 256
- FORCED SHUTDOWN 257
- 8-36 Troubleshooting 258
- Chapter 9 259
- ANTI-STATIC MEASURES 261
- PREPARATION FOR INSTALLATION 262
- Processor (CPU) 263
- 9-6 Upgrading Your Server 264
- 9. Lift the socket lever 267
- Front Rear 269
- Adding Order and Precautions 273
- Upgrading Your Server 9-17 275
- Key slot 276
- Mezzanine Card 278
- Type I Type II 282
- Hard Disk Drive 288
- 9-34 Upgrading Your Server 292
- 9-38 Upgrading Your Server 296
- Appendix A 297
- A-2 Specifications 298
- Appendix B 299
- System Update 300
- Setup Procedure 305
- The installation starts 312
- Install Windows – Insert Disc 317
- OK Cancel 317
- Alt + Del 319
- REMOTE DESKTOP FOR MANAGEMENT 331
- Windows Server 2003 332
- Setup of teaming 333
- Network Driver 334
- Graphics Accelerator 335
- Optional Network Board Driver 336
- Balancing (ALB) 338
- Setup Teaming 339
- SFT is not supported 340
- Remove Team 341
- SETTING WOL 342
- 4. Click [OK] 344
- 5. Reboot the system 344
- SETTING RECEIVE SIDE SCALING 345
- Local Update 352
- <Windows Server 2003> 355
- About Windows Activation 367
- 4. Activate Windows 369
Related products and manuals for Server/workstation motherboards NEC SigmaBlade B120a
(200 pages)© 2020, manymanuals.com. All rights reserved. | 2.229 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals