Nec NP2250 User Manual Page 159
- Page / 183
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
145
9. Appendix
Common Problems & Solutions
(
→
“Power/Status/Lamp Indicator” on page 144)
Problem Check These Items
Does not turn on • Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. (
→
page 22, 23)
• Ensure that the lamp cover is installed correctly. (
→
page 138)
• Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the
room where you are presenting is particularly warm, move the projector to a cooler location.
• Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end
of its life. If so, replace the lamp.
After replacing the lamp, reset the lamp hours used. (
→
page 133)
• The lamp may fail to light. Wait a full minute and then turn on the power again.
• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600
meters or higher. Using the projector at altitudes approximately 5500 feet/1600 meters or higher without
setting to [HIGH ALTITUDE] can cause the projector to overheat and the projector could shut down. If this
happens, wait a couple minutes and turn on the projector. (
→
page 127)
Also when the lamp is turned off, the projector internal temperature is hot. If the power is turned on before
the projector has cooled down, the fan will run a short time before the lamp will turn on.
Will turn off • Ensure that the [OFF TIMER], [PROGRAM TIMER] or [AUTO POWER OFF] is off. (
→
page 101, 127)
No picture • Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPUTER 1, the COM-
PUTER 2, the COMPUTER 3, the COMPONENT, the VIEWER or the NETWORK button on the remote control
to select your source. (
→
page 25)
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. (
→
page 90)
• Check to see if the image is muted. (
→
page 35)
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the Reset in the Menu. (
→
page 133)
• Enter your registered keyword if the Security function is enabled. (
→
page 45)
• Be sure to connect the projector and notebook PC while the projector is in standby mode and before turn-
ing on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector
before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-
saver or power management software.
• See also the next page.
Color tone or hue is
unusual
•
Check if an appropriate color is selected in [WALL COLOR]. If not, select an appropriate option. (
→
page
100)
• Adjust [HUE] in [ADJUST]. (
→
page 90)
Image isn’t square to
the screen
• Reposition the projector to improve its angle to the screen. (
→
page 26)
• Use the 3DReform function to correct the trapezoid distortion. (
→
page 30)
Picture is blurred • Adjust the focus. (
→
page 28)
• Reposition the projector to improve its angle to the screen. (
→
page 26)
• Ensure that the distance between the projector and screen is within the adjustment range of the lens. (
→
page 139, 140, 141)
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned
on. Should this happen, let the projector stand until there is no condensation on the lens.
Flicker appears on
screen
• Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately
5500 feet/1600 meters or lower. Using the projector at altitudes less than approximately 5500 feet/1600
meters and setting to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker.
Switch [FAN MODE] to [AUTO]. (
→
page 127)
Image is scrolling
vertically, horizontally or
both
• Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPUTER 1, the COM-
PUTER 2, the COMPUTER 3, the COMPONENT, the VIEWER or the NETWORK button on the remote control
to select your source (Video, S-Video, Computer, Component, Viewer or NETWORK). (
→
page 25)
•
Adjust the computer image manually with the [CLOCK]/[PHASE] in [ADJUST]
→
[IMAGE OPTIONS]. (
→
page 91)
Remote control does
not work
• Install new batteries. (
→
page 10)
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. (
→
page 10)
• Check if one or more remote sensors are enabled. Select [SETUP]
→
[INSTALLATION(2)]
→
[REMOTE
SENSOR] from the menu. See page 124.
• If the remote control cable plug is inserted into the REMOTE mini jack, the remote control does not function
wirelessly. See page 11.
• Make sure that the remote control’s ID corresponds with the projector’s ID.
• Selecting [ON] for [CONTROL ID] will not make the remote control supplied with the projector inoperable.
Indicator is lit or blinking • See the POWER/STATUS/LAMP Indicator. (
→
page 144)
Vertical stripes in RGB
mode
• Press the AUTO ADJUST button on the projector cabinet or the AUTO ADJ. button on the remote control. (
→
page 32)
•
Adjust the computer image manually with the [CLOCK]/[PHASE] in [ADJUST]
→
[IMAGE OPTIONS]. (
→
page 91)
USB mouse does not
work
• Make sure that your USB mouse is properly connected to the projector. (
→
page 37)
The projector may not support some brands of a USB mouse.
• Some menu items cannot be operated with a USB mouse.
For more information contact your dealer.
- NP3250/NP2250/NP1250 1
- Installation 5
- Important Safeguards 5
- Fire and Shock Precautions 6
- Lamp Replacement 7
- A Lamp Characteristic 7
- Remote Control Precautions 7
- About High Altitude mode 8
- Important Information 10
- Table of Contents 11
- 4. Convenient Features 12
- 5. Using the Viewer 12
- 7. Maintenance 13
- 8. Using Optional Lenses 13
- 9. Appendix 14
- 1. Introduction 15
- Features you’ll enjoy : 16
- About this user’s manual 17
- Part Names of the Projector 18
- Carrying the Projector 19
- To lock the carrying handle 20
- Top Features 21
- 7 8 1011 22
- 134 12 3 2 22
- 3D REFORM 23
- PIC-MUTE 23
- 7 m/22 feet 7 m/22 feet 24
- 7 m/22 feet 24
- USB(LAN) 25
- Distance (Unit 26
- WIRELESS 28
- AUDIO IN 31
- AUDIO OUT 31
- Component 31
- VIDEO OUT 32
- Connecting Your VCR 32
- USB Wireless LAN Unit 35
- To wall outlet 36
- Turning on the Projector 37
- AUTO ADJUST 38
- Selecting a Source 39
- LENS SHIFT 41
- LEFT RIGHT 41
- Focus ring 42
- Zoom lever 42
- Adjusting the Tilt Foot 43
- Screen frame 44
- Projected area 44
- Align left side 44
- [Poor picture] 46
- [Normal picture] 46
- Increase volume 46
- Decrease volume 46
- Using the Laser Pointer 47
- Turning off the Projector 48
- After Use 48
- Getting Integrated Help 50
- Changing Lamp Mode 50
- About Drag Mode: 53
- NERSTONE] 54
- Main picture 57
- Main picture Sub picture 57
- [POSITION] 58
- Disabling the Security 63
- Logging On 64
- Logging Off 64
- Creating or Adding a User 65
- Deleting a User 66
- Overview 67
- Preparation Before Use 67
- Structure of the HTTP Server 68
- [REMOTE DESKTOP] 74
- Setting the Remote Access 75
- Starting the Remote Desktop 76
- Exiting the Remote Desktop 78
- Supported movie files 80
- Using ArcSoft MediaImpression 80
- Projecting slides (Viewer) 81
- Operating Viewer Menu 81
- Projecting a movie file 82
- To display a movie file: 82
- Setting Option for Viewer 84
- THUMBNAILS menu 85
- Exiting Viewer 85
- Changing Background Logo 86
- When using the mouse: 95
- Menu tree 96
- Menu Elements 98
- 6. Using On-Screen Menu 100
- [ENTRY LIST] 100
- Using the Entry List 100
- [PICTURE] 102
- [PRESET] 102
- [DETAIL SETTINGS] 103
- [IMAGE OPTIONS] 105
- For VIDEO 107
- [NP3250/NP2250/NP1250] 108
- [NP3250W] 108
- INPUTSIGNAL 109
- Using Off Timer [OFF TIMER] 115
- Setting a new program timer 116
- Activating the program timer 117
- [INSTALLATION(1)] 121
- [INSTALLATION(2)] 124
- [NETWORK SETTINGS] 124
- [GENERAL] 125
- [PROJECTOR NAME] 126
- ACCOUNT LOCK 134
- [SECURITY] 135
- [OPTIONS] 140
- [USAGE TIME] 143
- [SOURCE (1)] 144
- [SOURCE (2)] 144
- [WIRED LAN] 145
- [WIRELESS LAN (1)] 145
- [WIRELESS LAN (2)] 146
- [VERSION (1)] 146
- [VERSION (2)] 146
- Replacing the Lamp 150
- Lens Shift Adjustable Range 155
- Replacing with Optional Lens 156
- Install the new lens 157
- Specifications 161
- Cabinet Dimensions 165
- Using the Chart 166
- List of Screen Sizes 168
- Signal Level 170
- Sync signal : TTL level 170
- Compatible Input Signal List 171
- PC Control Codes 172
- To GND of PC 173
- To RxD of PC 173
- To TxD of PC 173
- To RTS of PC 173
- To CTS of PC 173
- Troubleshooting Check List 177
- TravelCare Guide 179
Related products and manuals for Projectors Nec NP2250
Projectors Nec MT820 User Manual
(44 pages)
(44 pages)
Projectors Nec WT610E User Manual
(2 pages)
(2 pages)
Projectors Nec MT1045 User Manual
(42 pages)
(42 pages)
Projectors Nec NP4100 User Manual
(2 pages)
(2 pages)
Projectors Nec MT1075/MT1065 User Manual
(69 pages)
(69 pages)
Projectors Nec NP1250 User Manual
(6 pages)
(6 pages)
Projectors Nec DT100 User Manual
(55 pages)
(55 pages)
Projectors Nec NP110 User Manual
(92 pages)
(92 pages)
Projectors Nec NP300 User Manual
(6 pages)
(6 pages)
Projectors Nec LT81 User Manual
(55 pages)
(55 pages)
Projectors Nec XT9000 User Manual
(54 pages)
(54 pages)
Projectors Nec LT84/LT140 User Manual
(44 pages)
(44 pages)
Projectors Nec XT5000 User Manual
(46 pages)
(46 pages)
Projectors Nec MultiSync MT600 User Manual
(32 pages)
(32 pages)
Projectors Nec NP100/200 User Manual
(5 pages)
(5 pages)
Projectors Nec MT1000 User Manual
(44 pages)
(44 pages)
Projectors Nec NP1000 User Manual
(9 pages)
(9 pages)
Projectors Nec MT1035 User Manual
(53 pages)
(53 pages)
© 2020, manymanuals.com. All rights reserved. | 2.836 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals