NEC Express5800/R120d-2E SR User's Guide Page 139
- Page / 151
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2. System BIOS Setup
Express5800/R120d-2E User’s Guide
139
Chapter 3 Setup
2.4
Cases that Require Configuration
Only if a case applies to any of following cases, use the SETUP utility to change a parameter which was
configured as factory setting. Other than cases described below, do not change the settings. A list of SETUP
parameters and factory settings are described in Chapter 2 (1. System BIOS) in "Maintenance Guide".
Category Description Setting of parameter Remark
Basic Change date and time Configure date and time
Main → System Date
Main → System Time
Configurable on OS
On NumLock at power ON
Boot
→
Bootup Numlock State
→
On
Off the function to display the
logo during POST
Boot → Quite Boot → Disabled
By pressing the <Esc> key,
prevent the display of the logo.
Memory
Memory configure after add or
change DIMM
Advanced → Memory Configuration →
Memory Retest → Yes
After rebooting, Memory Retest
changes No automatically.
Use memory RAS feature Change to RAS mode
Advanced → Memory Configuration →
Memory RAS Mode
You can select Mirroring, Lock
Step, or Sparing.
Optional
board
Disable Option ROM Scan of
installed option board
Advanced → PCI Configuration → PCI
Device Controller and Option ROM
Settings → PCIXX Slot Option ROM →
Enabled
XX is PCI slot number of the
option board
Boot
Change the boot order of
devices
Change the boot priority
Boot → Boot Option Priorities
When you use
EXPRESSBUILDER, set
CD/DVD to the highest priority.
Use remote power on feature
(via modem)
Advanced → Advanced Chipset
Configuration → Wake On Ring →
Enabled
Use remote power on feature
(via RTC alarm)
Advanced → Advanced Chipset
Configuration → Wake On RTC Alarm
→ Enabled
Use console redirection feature
Advanced → Serial Port Configuration
→ Console Redirection Setting →
Change respective setting.
Security
Set a password to restrict
operation of SETUP Utility
Set a password
Security → Administrator Password
Security → User Password
If password is set, a
message to enter password
is displayed at next time
SETUP is launched.
Set a password to restrict Boot
Security → Password On Boot →
Enabled
You can select this parameter
after you set password.
UPS
Powerlink
When the server is supplied
with power from UPS, always
turn on the power.
Server → Power Control
Configuration → AC-LINK → Power
On
If it is turned off by using
POWER switch, leave it OFF
even when UPS supplies
power.
Server → Power Control
Configuration → AC-LINK → Last
State
Keep the power OFF even
when UPS supplies power.
Server → Power Control
Configuration → AC-LINK → Stay off
- Express5800/R120d-2E 1
- EXP481A 1
- User’s Guide 1
- Contents 3
- Trademarks 8
- Regulatory Notices 9
- Latest editions 10
- CAUTION 11
- Symbol to draw 12
- Description of a warning 12
- Warning labels 19
- Handling precautions 20
- General Description 22
- Introduction 23
- Accessories 24
- Standard Features 25
- Management Features 28
- Names and Functions of Parts 30
- Rear View 36
- External View 38
- Internal View 39
- Motherboard 40
- Status Indicators 41
- 2.5-inch hard disk drive 44
- 3.5-inch hard disk drive 44
- 4 M3 2 1 45
- AC POWER LED 47
- Primary power 47
- Preparations 48
- Safety Precautions 49
- Anti-static Measures 50
- UID switch 53
- Removing the Front Bezel 55
- Removing Top Cover 56
- Internal Flash Memory 57
- TPM Kit 58
- Processor (CPU) 59
- Pin mark 60
- Memory Clock 63
- Memory RAS Feature 64
- Installation 66
- Using Memory RAS Features 68
- Blue line at left end 71
- Backup File Device 73
- USB cable 74
- Power cable 74
- PCI Card 76
- Additional HDD Cage 85
- DC cable 87
- Additional HDD Cage (Rear) 88
- Redundant Fan Unit 90
- Important 91
- Optical Disk Drive 93
- Connecting cables 96
- Installing Top Cover 102
- 2.5-inch Hard Disk Drive 103
- 3. Remove the dummy trays 105
- 6. Slowly close the handle 106
- DISK LED 107
- Removal 107
- 3.5-inch Hard Disk Drive 109
- Installation 110
- Power Supply Unit 113
- 2. Remove the blank cover 114
- 4. Connect power cords 115
- 5. Power on the server 115
- Installing Front Bezel 117
- Installation and Connection 118
- Release lever 123
- Locking 123
- Locked state 123
- Rail Stopper 124
- Front View 125
- Locking mechanism 125
- Unlock lever 125
- Connection 126
- USB device 127
- Display unit 127
- NEC Express5800 Series 131
- Turning on the Server 132
- POST error messages 135
- System BIOS Setup 136
- EXPRESSSCOPE ENGINE 3 141
- EXPRESSBUILDER 143
- Turning Off the Server 145
- Appendix 146
- Specifications 147
- PCI Configuration 149
Related products and manuals for Servers NEC Express5800/R120d-2E SR
Servers NEC Express5800/HV8600 User's Guide
(204 pages)
(204 pages)
Servers NEC Express5800/120Lf User's Guide
(198 pages)
(198 pages)
Servers NEC Express5800/120Rh-1 User's Guide
(190 pages)
(190 pages)
Servers NEC Express5800/T110g-S User's Guide
(128 pages)
(128 pages)
Servers NEC Express5800/120Rg-2 User's Guide
(338 pages)
(338 pages)
Servers NEC Express5800/120Rj-2 User's Guide
(206 pages)
(206 pages)
Servers NEC SigmaBlade B140a-T User's Guide
(376 pages)
(376 pages)
Servers NEC Express5800/120Li User's Guide
(344 pages)
(344 pages)
Servers NEC Express5800/1160Xd User's Guide
(214 pages)
(214 pages)
Servers NEC Express5800/R110d-1E User's Guide
(133 pages)
(133 pages)
Servers NEC MC2400 User Manual
(204 pages)
(204 pages)
© 2020, manymanuals.com. All rights reserved. | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals